Selection of a table or map

2018/26

2009/17

2004/06

1993/95

1983/85

Altitude above sea level in classes of 400 m. Reference: Digital height model DHM 25 from Swisstopo

Altitudinal vegetation belts in the system used in the guidelines for monitoring the sustainability and performance of protection forests (NaiS; Frehner et al. 2005), reduced to six classes. The variable represents a simplification of the NaiS altitudinal vegetation belts with ten classes (NAISHSTKOMB) in which the classes «hyperinsubric» and «colline» are merged with «colline with beech» to form the class «hyperinsubric and colline» and the class «lower montane» with «upper montane» and «lower/upper montane» to form the class «lower and upper montane». The information is based on the altitudinal vegetation belts determined by experts (accessible forest sample plots of NFI4 on the 1.4-km network; Arge Frehner et al. 2020), as well as on the altitudinal vegetation belts modelled for the period 1981-2010 (other sample plots; Zischg et al. 2021). n/a: located above the forest boundary modelled by Zischg et al. and sometimes in the area of lakes, which were relatively roughly cut out by Zischg et al.

Sample plots without/with gaps ≥100 m² from canopy edge to canopy edge that intersect with the interpretation area (50 × 50 m), classified according to the area of the largest gap into five classes. Reference: aerial photo interpretation

Proportion of the ground area covered by tree crowns according to the aerial photo interpretation – in five 20-percent classes. The percentage is calculated using the 25 grid points on the interpretation area (50 × 50 m). Reference: aerial photo interpretation

Classification of forests into 12 classes («types») according to their development, structure and management. Unlike in the 17-class forest-type classification, in this 12-class classification all development stages (from young growth to timber) are subsumed in the class «uniform high forest». Reference: Field Survey (MID 255: Nutzungskategorie, MID 257: Waldtyp nach Aufnahmeanleitung LFI, MID 260: Waldform, MID 267: Bestandesstruktur, MID 261: Entwicklungsstufe)

Demarcation of Switzerland into five regions (Jura, Plateau, Pre-Alps, Alps and Southern Alps) with relatively uniform growth and timber production conditions. The production regions were established by the Federal Office of Forestry long before the first National Forest Inventory (NFI1, 1983-1985). With a small exception along Lake Geneva, the boundaries of the production regions still follow the municipal boundaries of the time. Unlike the NFI, the Forestry Statistics of the Federal Statistical Office don't use the production regions as demarcation but rather the forestry zones, whose boundaries are somewhat different.

Division of Switzerland into 14 regions (2 in the Jura, 3 on the Plateau, 3 in the Pre-Alps, 5 in the Alps and 1 in the Southern Alps). The economic regions are a subdivision of the production regions according to economic-geographical criteria.

Demarcation of Switzerland used in NFI for protective forest analyses. The six protective forest regions were derived from the economic regions by combining individual regions according to natural and statistical criteria.

Regional demarcation with the cantons as a unit, with the two half-cantons, Basel-Land and Basel-Stadt, combined into one canton for statistical reasons.

Demarcation of Switzerland into six regions with similar flora and fauna. The six regions correspond to the basic categories in the publication «The Biogeographical Regions of Switzerland», which was published by FOEN in 2022.

Sub-grids 1, 2, 3, 4 and 5 of 9 on the sampling grid with a mesh size of 1.4 km (base grid).

NFI's sampling grid with a mesh size of 1.4 km. The 1.4-km grid is the grid size covering all the previous terrestrial Inventories, which is why it is also called the base grid.